Updated November 2026

DIY baby proofing electrical cords means shortening loose cords, anchoring them out of reach and bundling the extras so a toddler can’t pull a lamp down, chew a charger or wrap a cord around their neck. You can do most of this in one afternoon with inexpensive supplies and a tape measure. The steps below work for lamps, phone chargers, window blind cords and appliance cords.

Start With a Cord Audit

Walk through each room at toddler height and make a list of every cord you find. Crouch down, since most of what a one-year-old can reach sits between the floor and about 36 inches. Pay special attention to cords that run along the floor, hang off countertops, or stretch across walking paths, because these are the ones that get yanked.

Shopping for one? See our guide: Baby Proofing Service Houston: 7 Best Options Compared (2026).

Note whether each cord is still connected to a live outlet. Unplugged cords can still be chewed or pulled, so they deserve the same treatment.

Shorten, Secure and Hide Cords

Take up slack

Loose cord length is the biggest hazard. Gather excess cord into loose loops and secure them with a hook-and-loop tie placed well away from the plug. Never wrap cord tightly around the appliance, and never tie a knot, since heat and strain can damage the wire over time.

Anchor cords to walls and furniture

Use adhesive cord clips or cable raceways to run cords flat against baseboards or the back of furniture. Keep cords off the floor where a child can grab them, and keep them clear of rugs, where they can be tripped over or pulled from under a rug edge.

Cover and enclose the rest

Plastic cord covers or raceways hide cords and prevent chewing. Choose a cover wide enough to fit the cord without pinching it. Check the cover every few weeks, because adhesive can loosen, especially on textured walls.

Handle Window Blind and Appliance Cords

Corded window blinds are a strangulation risk. Cut off loops, fit cord cleats or tension devices, and raise blinds out of reach or switch to cordless models. Appliance cords should be pulled back behind the unit or stored when not in use. Keep cords for space heaters, slow cookers and irons unplugged and stored after each use.

Checklist for DIY Cord Proofing

  1. Crouch to toddler height and list every cord in the room.
  2. Remove or cut loops of excess cord and secure them with hook-and-loop ties.
  3. Attach cord clips or raceways to baseboards and furniture backs.
  4. Fit covers over any cord that runs across a floor or wall.
  5. Check window blind cords and install cleats or tension devices.
  6. Recheck everything after a week and tighten loose adhesive.

Common Mistakes

  • Wrapping cords too tightly, which stresses the insulation.
  • Using cord covers that are too small and pinch the wire.
  • Leaving cords under rugs or running them across doorways.
  • Forgetting unplugged cords, which toddlers still chew.
  • Assuming adhesive will last indefinitely on painted or textured surfaces.
  • Cord cover raceways hide and protect runs along walls and baseboards. View on Amazon
  • Hook-and-loop cable ties bundle excess slack without knots or tight wraps. View on Amazon
  • Adhesive cord clips hold cords flat against furniture backs and baseboards. View on Amazon

FAQ

Are cord covers safe to use on every cord?

Cord covers are designed for low-voltage and household cords, but they should never be used on cords that feel hot or show damage. Replace any frayed or cracked cord rather than covering it. Consult a licensed electrician if you are unsure about an outlet or wiring issue.

How high should cords be kept?

Keep cords well above the reach of a toddler standing on the floor and clear of any surface they can climb. Many parents also keep cords out of reach of a child on a step stool, since climbing is common by the second year.

Can I use tape instead of cord clips?

Standard tape is not a reliable long-term fix because it can leave residue, peel, or let a child pull the cord free. Use purpose-made clips or raceways for anything that needs to stay put.

Conclusion

Shortening, securing and covering cords removes the most common electrical hazards in a toddler’s home. Work through each room at toddler height, and recheck your fixes every few weeks. For wiring or outlet problems, consult a licensed electrician.

Graham Fisher

About Graham Fisher

Graham Fisher is part of our editorial team and reviews and edits our childproofing guides, checking product details against manufacturer specifications and owner feedback.