Updated November 2026

Baby proofing an open staircase means blocking access to the stairs when no adult is supervising and closing the gaps that let a toddler slip through or over the railing. Most of the work comes down to three things: a properly fitted gate at the top and bottom, a railing or baluster barrier that stops small bodies from squeezing through, and a clear routine for who closes what. Follow the steps below and you will have a setup that holds up to daily toddler traffic.

Step 1: Measure the Openings Before You Buy Anything

Start by measuring the width of each opening you need to block. Measure at the narrowest point, usually at the top of the staircase where the wall meets the railing, and measure again at the bottom. Many gate manufacturers specify a width range for their hardware-mounted and pressure-mounted models, so write down the minimum and maximum width for each spot. Also note the height of the top rail, since that determines whether a standard gate will clear the floor and the handrail.

Shopping for one? See our guide: 8 Best Baby Proofing Open Concept Gates and Barriers for Wide Living Spaces.

Pressure-mounted gates are only suitable for doorways and hallways. Stairs need a hardware-mounted gate that screws into the wall or the stair post, because a pressure gate can loosen and fall backward when a child pushes on it. Manufacturers generally advise against mounting any gate across the top of a staircase with pressure alone.

Step 2: Install a Hardware-Mounted Gate at the Top

The top of the stairs is the higher-risk location, so install the gate there first. Check the gate instructions for the required mounting method, which usually means drilling into a wall stud or a solid post. Confirm that the gate opens away from the stairs, so a toddler leaning on it cannot push it open and fall through. Test the gate by pushing and shaking it firmly with both hands before you let your child near it.

  • Use a stud finder and mount into solid wood, not drywall alone.
  • Choose a gate that swings toward the room, not over the stairs.
  • Keep the latch at adult height and make sure it cannot be lifted by a child.

Step 3: Block the Gaps Along the Railing

Even with a gate at the top, open railings can let a child push a foot or head through the balusters. Measure the gap between each baluster. If it is wider than about 4 inches, which is the common benchmark used in building codes for guardrail openings, add a barrier. Options include a clear safety mesh stretched across the railing, a rigid panel fastened to the posts, or a stair-specific net. Secure every barrier so that no part can be pulled loose by a child standing on the bottom step.

Pay attention to the area where the stair railing meets the wall. Small gaps there can trap fingers or let a toddler reach through, so fill them with foam or a flexible cover designed for the purpose.

Step 4: Add a Bottom Gate and Remove Tripping Hazards

A bottom gate keeps toddlers from climbing up unsupervised and reduces the chance of a fall from the lower steps. Use the same measuring and mounting approach as the top gate. Next, check the stairs themselves. Remove toys, shoes and laundry from the steps, and make sure runners or rugs are fastened tightly to each tread. A loose rug edge is one of the most common causes of stair tumbles in toddler homes.

Step 5: Set a Routine and Test Regularly

Hardware and barriers only work if they are closed every time. Make it a habit to check the top gate latch each time you pass it, and ask anyone who babysits or visits to do the same. Once a month, push on every gate, check every barrier for looseness and confirm that mounting screws have not backed out. Toddlers grow quickly and learn new tricks, so reassess the setup whenever your child reaches a new milestone.

Common mistakes

  • Using a pressure-mounted gate at the top of the stairs.
  • Installing a gate that swings over the stairs, which can let a child fall through when it opens.
  • Leaving the railing gaps open because the gate seems to be enough.
  • Forgetting to recheck gates after a few months of daily use.
  • Leaving the bottom gate open while carrying laundry or groceries up the stairs.
  • Hardware-mounted safety gate: Designed to screw into the wall or stair post, so it stays put when a child pushes or climbs on it. View on Amazon
  • Stair railing safety netting: Covers open balusters so a toddler cannot push a head or foot through the gaps. View on Amazon
  • Gap filler foam strips: Fill narrow spaces where the railing meets the wall to close off finger-trap and reach-through openings. View on Amazon

FAQ

Can I use a pressure-mounted gate at the top of the stairs?

No. Pressure-mounted gates can loosen and fall when a child pushes against them, which makes them unsafe at the top of a staircase. Use a hardware-mounted gate there instead.

How wide can the gaps in a staircase railing be?

Many building codes use about 4 inches as the maximum opening for guardrails. If your balusters are spaced wider than that, add a barrier to close the gaps.

Should I mount the gate on the stairs or the wall?

Mount it into a wall stud or solid stair post, following the manufacturer’s instructions. Drywall alone will not hold up to repeated pushing.

Conclusion

A baby proofed open staircase combines a hardware-mounted gate at the top, a secure bottom gate and barriers along the railing. Measure carefully, mount into solid structure and check everything monthly. For guidance specific to your home, a licensed contractor or your gate manufacturer’s support line can help confirm the right fit.

Graham Fisher

About Graham Fisher

Graham Fisher is part of our editorial team and reviews and edits our childproofing guides, checking product details against manufacturer specifications and owner feedback.