Updated November 2026

A toddleroo by North States baby gate 8 panel is a pressure-mounted or hardware-mounted gate designed to block a wide opening, such as a hallway or the wide side of a family room. This guide walks you through measuring the opening, confirming the gate fits, installing it securely and checking it over time. Work through each step before your toddler starts testing it.

Measure the Opening Before You Buy or Install

Start by measuring the width of the opening at the floor, mid-height and top, since walls are rarely perfectly square. Check the manufacturer’s stated width range for your model and confirm your measurement falls within it, with a little room to spare. Note any baseboards, trim or door casings that could interfere with the mounting points or the gate’s frame.

Shopping for one? See our guide: North States 72 Wide Deluxe Décor Baby Gate Review: Features and Performance.

Also measure the height from the floor to the top of the gate. Your toddler’s ability to climb matters more than their age, so a gate that looks tall enough on paper may still be too short if your child is a confident climber. If you are unsure whether the gate suits your child, a pediatrician or a childproofing professional can help you judge.

Choose Pressure or Hardware Mounting

An 8-panel gate spans a wide space, and that length puts more stress on the mounting. Pressure-mounted gates depend on tension against two walls, which works best on smooth, level surfaces without outlets or thin drywall at the contact points. Hardware-mounted installation screws into the wall studs and is the safer choice for stairs and any opening where a fall would be serious.

Never use a pressure-mounted gate at the top of stairs. Manufacturers generally specify hardware mounting for stair tops, and that is a rule worth following without exception.

Install the Gate Step by Step

  1. Assemble the panels following the included instructions, and confirm that all joints and latches are fully seated.
  2. Locate wall studs with a stud finder and mark the mounting points so the screws land in solid wood, not drywall alone.
  3. Attach the wall-side mounting hardware first, keeping everything level as you go.
  4. Set the gate in place, connect it to the mounts, and tighten all fasteners fully.
  5. Test the latch with both hands, then push and pull hard against the gate from both sides.
  6. Shake the gate firmly to check that nothing wobbles, shifts or pulls loose from the wall.

For more detail on how gates of this style are fitted, see Munchkin Xl Baby Gate Instructions: Step-by-Step Install Guide (2026), which covers similar hardware steps.

Run a Safety Check Every Month

Once the gate is installed, inspect it at least once a month. Look for loose screws, bent panels, worn latch springs and gaps that have opened up at the mounts. Toddlers tend to push, pull and lean on gates, and that slowly loosens fittings over time.

Pay attention to the gap between the gate and the floor, and between the panels themselves. A gap large enough for a head or a foot is a hazard, so check those spaces as well. For a broader room-by-room view of where gates are most useful, see Do I Need a Baby Gate? A Room-by-Room Checklist to Decide (2026).

Common Mistakes to Avoid

  • Installing a wide gate with only pressure mounts when the opening is large and heavily used.
  • Screwing into drywall alone instead of finding the studs.
  • Leaving a gap at the bottom that a child could slip a foot or head through.
  • Skipping the monthly check and assuming a gate that was secure on day one will stay that way.
  • Using the gate as a climbing surface, or placing furniture near it that gives a child a step to climb.
  • Stud finder: Helps you locate solid wood for hardware mounting, which is the most important step for a wide, heavy gate. View on Amazon
  • Level: Keeps the gate straight so the latch lines up and the panels sit evenly. View on Amazon
  • Cordless drill with driver bits: Makes driving the mounting screws into studs faster and more consistent. View on Amazon

FAQ

Can I install a toddleroo by North States baby gate 8 panel at the top of the stairs?

Check the manufacturer’s instructions first, since top-of-stairs installation usually requires hardware mounting and specific clearance rules. If you are unsure, ask a qualified installer to confirm the setup before relying on it.

How do I know if the gate is wide enough for my doorway?

Measure the opening at the floor, middle and top, then compare the smallest reading against the width range listed for your model. Allow a little extra room so the gate can be installed without forcing it.

How often should I check the gate for wear?

A monthly check is a sensible routine for most households. Look at screws, latches, mounts and gaps, and tighten or replace anything that has loosened or worn.

Conclusion

Measure carefully, choose the right mounting method for the location, and install the gate into studs wherever possible. Test the latch and the fit after installation, then check everything again each month. A gate that is properly fitted and maintained will keep your toddler safe in the spaces where you need it most.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our childproofing guides, checking product details against manufacturer specifications and owner feedback.