Updated November 2026

Outlet covers that cover the whole outlet are a simple, effective way to stop a toddler from poking fingers or objects into the slots. Unlike plug-in inserts that only fill the openings, these covers sit over the entire receptacle and close off the face of the outlet. This guide explains what to look for, how to decide between sliding, hinged, and solid-face designs, and how to install one correctly so it stays put.

What “Covering the Whole Outlet” Actually Means

A whole-outlet cover, sometimes called a face cover or full-face cover, is a plate or shell that spans the entire duplex receptacle, including the area around the two slots and the ground hole. Many people search for this when they have already tried plug inserts and found that toddlers pull them out, or when they want a cleaner look on a wall they are working to childproof.

Shopping for one? See our guide: 7 Best Outlet Covers for Floor Installations Compared (2026).

Whole-face covers generally fall into three types:

  • Solid-face covers that have no openings at all. These cannot be used while something is plugged in, so they suit outlets you rarely use or cords you can route elsewhere.
  • Sliding or shutter covers that open with a finger or a tab when you need to plug something in and close again on their own.
  • Hinged or flip covers that lift up on a pin and rest against the wall or a spring stop.

Before you buy, confirm whether you need a cover that stays closed permanently or one that you will open regularly. Your answer shapes everything else.

Step 1: Measure and Match Your Outlet

Most standard US duplex outlets are roughly 2.75 inches wide by 4.5 inches tall when measured from the outer edges of the cover plate. Decora-style rocker switches and some decorator outlets use slightly different footprints, so measure before you buy. Check the following:

  1. Count the gangs. A single outlet, a switch plus outlet, or a double outlet each need a plate sized to match.
  2. Check the mounting screw spacing. Standard screws are about 3 inches apart on center for single gangs.
  3. Look at the wall box depth. Some full-face covers need extra clearance behind the plate. Manufacturers specify this, and it matters most in older homes with shallow boxes.
  4. Note the surface. Painted drywall, plaster, and wood paneling all accept the same covers, but plaster may need a slightly thicker mounting bracket.

Step 2: Confirm the Outlet Is Safe to Work On

Installing a cover means removing the existing plate and sometimes the device itself. Turn off power at the breaker before touching anything, and test the outlet with a non-contact voltage tester to confirm it is dead. If you see scorch marks, hear buzzing, or find loose wiring, stop and call a licensed electrician. Outlet work is not a good place to guess.

Step 3: Choose the Right Style for Your Household

Each style solves a different problem. The table below compares the most common choices by how they handle daily use.

Cover Type Best For Limitation
Solid-face Unused outlets, outlets behind furniture Cannot be used while open or plugged in
Sliding shutter Outlets used daily that need quick access Shutter can wear or stick over time
Hinged flip Outlets with a plug that stays in place Hinge may loosen; check it regularly
Tamper-resistant with cover Homes that need code-compliant hardware Still needs a cover for full protection

Tamper-resistant receptacles have internal shutters that block foreign objects from the slots. They are required in many newer US homes, but they are not a substitute for a cover over the whole face. For background on the difference, see Outlet Covers and Tamper-Resistant Outlets Explained.

Step 4: Install the Cover

Gather your tools

  • Non-contact voltage tester
  • Phillips and flat-blade screwdrivers
  • Level (optional, but helpful on long plates)
  • Painter’s tape to protect the wall
  • The cover kit, including the correct mounting screws

Remove the existing plate

  1. Switch off the breaker and verify with your tester.
  2. Unscrew the old plate and set the screws aside.
  3. Take a photo of the wiring before disconnecting anything.

Mount the new cover

  1. Attach the mounting bracket or base to the outlet using the screws supplied. Do not overtighten, since a cracked receptacle is hard to replace.
  2. Check that the cover sits flush against the wall. A gap lets small fingers slip behind it.
  3. Test the shutter or hinge by operating it several times. It should close fully on its own or with light pressure.
  4. Restore power and test the outlet with a plug in and out.

If your cover uses screwless clips, follow the manufacturer’s instructions exactly. Some clips require a specific depth of insertion to hold.

Step 5: Test the Cover Like a Toddler Would

Once installed, spend a few minutes trying to get at the outlet the way a curious child would. Push on each edge with a fingertip. Try to pry the cover with a small object. Look for gaps between the cover and the wall, especially at the corners. If you can get anything into the slots, adjust the fit or choose a sturdier model.

Common Mistakes

  • Buying the wrong size. A plate that is slightly too small leaves a gap, and one that is too large may not sit flat against the wall.
  • Leaving a plugged-in cord under a solid cover. Cords can overheat or get pinched. Route the cord out through an approved path or switch to a shutter design.
  • Overtightening screws. This can crack the receptacle or bend the bracket.
  • Assuming a cover replaces tamper-resistant outlets. Covers and internal shutters work together; neither is a full substitute for the other.
  • Forgetting to check later. Shutters loosen, and children sometimes pull at hinges. Inspect covers monthly.

Tips for Long-Term Use

  • Label any solid-face covers on outlets you plan to use later so the next person does not remove them without thinking.
  • Use a whole-face cover on outlets near cribs, play areas, and bathroom sinks first, since these are the highest-risk spots.
  • Keep spare screws in a labeled bag in case one is lost during cleaning.
  • For outdoor or damp locations, use a weather-rated cover instead of an indoor model.
  • If you are unsure whether an outlet is wired correctly, have an electrician check it before you add a cover.

These items help with the measuring and installation steps above.

  • Non-contact voltage tester, which lets you confirm the circuit is dead before you remove any hardware. View on Amazon
  • Painter’s tape, which protects wall paint around the plate while you work. View on Amazon
  • Phillips screwdriver set with insulated handles, which gives you a good grip on small outlet screws. View on Amazon

FAQ

Do outlet covers that cover the whole outlet stop a toddler from using the outlet?

They stop access to the slots and ground hole while the cover is closed. Shutter and hinged styles let you use the outlet when needed, while solid-face covers keep it fully blocked.

Can I install a whole-face cover on a GFCI outlet?

Many covers fit GFCI receptacles, but the GFCI test and reset buttons must remain accessible. Check the cover’s specifications and confirm the buttons are not blocked. Consult a licensed electrician if you are unsure.

Are these covers required by code?

Building codes generally require tamper-resistant receptacles in many areas of newer homes. Full-face covers are an added layer and are not usually a code requirement. Check local rules with your building department.

How do I remove a cover without damaging the wall?

Unscrew the cover and any base bracket first. For screwless models, follow the release method in the instructions, often a gentle pry at the edge with a thin tool. Peel any tape slowly.

Will a cover work on a switch plate?

Covers are sized for receptacles, but some manufacturers make combination plates for switch and outlet gangs. Match the gang count exactly.

Can a cover overheat an outlet?

A closed cover with nothing plugged in should not cause overheating. Problems arise when a plug is forced under a solid cover or when the cover traps heat from a high-draw device. Do not cover outlets that power heaters or other high-wattage appliances.

How often should I check covers?

Check them at least monthly for looseness, cracks, and shutter wear, and after any time a child has been tugging at them.

Are outdoor covers different?

Yes. Outdoor covers are rated for moisture and temperature changes. For guidance, see Top 7 Weatherproof Electrical Outlet Covers for Outdoor Walls.

Conclusion

Outlet covers that cover the whole outlet give you the most complete protection against curious fingers and objects. Measure carefully, choose a style that matches how often you use the outlet, and test the installation before you walk away. Revisit your covers regularly, since hardware loosens over time. If any step feels beyond your comfort level, a licensed electrician can handle it quickly.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our childproofing guides, checking product details against manufacturer specifications and owner feedback.