Updated November 2026

Low voltage outlet covers are plastic or composite plates designed to block access to low-voltage outlets, such as those used for phone, data, coaxial cable, and some doorbell or thermostat wiring. This guide explains what those outlets are, how they differ from standard 120-volt receptacles, and how to choose and install covers that keep curious toddlers from poking fingers or small objects into openings. By the end, you will have a room-by-room method for finding these outlets and sealing them properly.

Why Low Voltage Outlets Still Need Covers

Many parents focus on the standard household outlets and forget the smaller jacks on the same wall. A low voltage outlet typically carries signal, not household power, so the shock risk is far lower than with a 120-volt receptacle. That does not make it harmless. Toddlers can still push a paperclip, a bead, or a bit of food into an open jack, damage the wiring, or pull on exposed cable. A cover that fits snugly removes the temptation entirely and keeps the wall looking tidy.

Shopping for one? See our guide: 7 Best Outlet Covers for Floor Installations Compared (2026).

Low voltage jacks are also commonly installed at the same height as standard outlets, often just a few inches away, so they sit squarely within a toddler’s reach. Treat them as part of your outlet safety plan rather than an afterthought.

Step 1: Map Every Low Voltage Outlet in the Home

Before you buy anything, walk through each room and note every low voltage jack. Common types include:

  • Coaxial (cable TV) jacks, usually round with a center pin
  • Ethernet or RJ-45 jacks, rectangular and slightly wider than a phone jack
  • RJ-11 telephone jacks, smaller and narrower
  • Speaker wire terminals and some audio jacks
  • Thermostat, doorbell, or security system wiring plates

Mark each one with painter’s tape or a sticky note so you can see the full count. Many homes have low voltage jacks in media rooms, home offices, bedrooms, and kitchens near the counter. Some are on the floor or low on the wall in older houses, which matters for toddler height.

Measure Each Plate

Low voltage plates come in several sizes and configurations. Note the number of openings, the plate width and height, and the screw spacing. Many low voltage wall plates use a standard single-gang or double-gang footprint, but the openings differ. A cover made for a two-port Ethernet plate will not fit a single coaxial jack properly.

Step 2: Choose the Right Cover for Each Jack

Once you have your inventory, match each jack to a cover type. Consider these factors:

Factor What to Check Why It Matters
Opening count Single, double, or multi-port Covers must block every opening
Jack type Coax, RJ-11, RJ-45, or wire Shape determines fit and sealing
Mounting style Screw-mounted or screwless Screwless designs suit toddler-accessible walls with no screws to loosen
Material Polycarbonate, nylon, or similar Impact resistance and durability
Wall depth Flush or raised Affects how the plate sits against drywall

Some low voltage plates are cable pass-through designs. If a cable must run out of the wall, choose a cover with a cable opening sized for that wire, then fill the gap with a slim foam or silicone stopper where the cable exits. Avoid leaving a wide gap that a child can enlarge.

Screwless Versus Screw-Mounted Covers

Screwless covers use a friction or snap-on design with no exposed hardware. Screw-mounted covers rely on the same screws that hold the original plate. Screwless models are popular in toddler homes because nothing is left to unscrew and swallow. Read the manufacturer’s installation instructions to confirm the plate’s screw spacing and wall box compatibility before buying. For a deeper comparison of mounting styles, see Outlet Covers Without Screws (2026): Which Should You Choose?.

Step 3: Gather Tools and Supplies

Most installations take under 15 minutes per cover. You will need:

  1. A Phillips screwdriver and, if needed, a flat-head screwdriver
  2. A voltage tester or a non-contact tester (recommended even for low voltage wiring)
  3. Painter’s tape and a pencil for marking
  4. A soft cloth to clean the wall plate surface
  5. Replacement screws if the included ones do not match the wall box

Turn off power to any nearby standard outlets if you are working in the same box, even though low voltage jacks themselves carry no household current. This habit prevents mistakes.

Step 4: Install the Covers Safely

Prepare the Wall Plate

Remove the existing plate by unscrewing it gently. Keep the screws in a small dish. Inspect the cable or wire connections behind the plate. If wires are loose, stop and call a licensed electrician. Do not attempt to re-terminate telecom or security wiring unless you are trained.

Seat the Cover

Position the new cover over the jack so that every opening is fully exposed to the cover’s blocking design. Align the mounting holes with the wall box. For screw-mounted models, tighten the screws until the cover sits flush without cracking the plastic. For screwless models, press the cover evenly around the edges until it clicks or seats firmly.

Test the Fit

Try to push a thin object such as a paperclip toward each opening. The cover should prevent it from reaching the jack. Then gently tug the cover to confirm it does not shift. If it wobbles, the cover may not match the plate size.

Step 5: Check and Maintain Coverage

Set a reminder to inspect covers every few months, especially in rooms where toddlers play near the wall. Look for cracks, loosened screws, or gaps around cable exits. Replace any cover that no longer blocks an opening. Electrical and cable systems change as you add devices, so re-check coverage after any new installation.

Common Mistakes

  • Buying covers by room instead of by jack count, leaving one port exposed.
  • Forcing a cover onto a mismatched plate, which can crack the cover or loosen the wall box.
  • Leaving a large gap around a cable, which a child can widen.
  • Assuming low voltage means no hazard. Wires can still be pulled, chewed, or damaged.
  • Using decorative covers that are easy to pry off without checking the locking design.
  • Forgetting floor-level or baseboard jacks in older homes.

Tips

  • Keep a spare cover of each size on hand for quick replacements.
  • Photograph each jack and its cover before installation so you can match replacements later.
  • If a cable must stay exposed for your setup, consider relocating the device or using a wall box with a built-in cover.
  • Teach older children that low voltage jacks are not for toys or pencils.

A few supplies make this project easier and safer:

  • Non-contact voltage tester: Confirms the circuit state of nearby standard outlets before you work near the same box. View on Amazon
  • Screwless low voltage plate covers: Remove screws as a swallowing hazard and suit walls with frequent toddler contact. View on Amazon
  • Silicone cable grommets: Seal cable exits so openings stay small. View on Amazon

FAQ

Are low voltage outlets dangerous to toddlers?

They carry much less electrical energy than standard outlets, so shock risk is lower. However, children can still insert objects, damage cables, or injure themselves on exposed hardware. Covering them is a sensible precaution.

Do low voltage outlet covers need to be tamper-resistant?

Tamper-resistant designs are required for standard 120-volt receptacles under current US code, not for low voltage jacks. Still, a snug, locking cover is useful for any opening a toddler can reach.

Can I use the same cover for phone and Ethernet jacks?

Only if the cover is rated for both jack shapes and sizes. Check the product’s specification sheet, since many covers are designed for one configuration.

Should I cover a coaxial jack that is not in use?

Yes. Unused jacks are exactly the openings toddlers find most interesting, and an unused jack can still be pulled or pressed.

Do I need an electrician to install low voltage covers?

Most cover installations are simple screw or snap work. If you find damaged wiring, exposed conductors, or any sign of heat, stop and consult a licensed electrician.

Can I paint a low voltage outlet cover?

Some plastic covers accept paint designed for plastic surfaces, but painting can affect fit and make the surface slippery. Check the manufacturer’s guidance first.

How often should I check low voltage outlet covers?

Inspect them every few months and after rearranging furniture or adding devices. Replace any cracked or loose cover promptly.

What if a cable runs through the wall plate opening?

Choose a cover with a pass-through opening sized for that cable, then seal any gap with a slim foam or silicone stopper. Avoid leaving a space wide enough for a child’s finger.

Conclusion

Low voltage outlet covers close a gap that many childproofing plans miss. Map every jack, match each one to a cover that blocks all openings, and install with care. Check coverage regularly, especially as your home and devices change. A few minutes of attention now keeps the smaller outlets on your walls as safe as the larger ones.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our childproofing guides, checking product details against manufacturer specifications and owner feedback.