Updated November 2026
Paintable outlet covers from Lowe’s let you blend a child-safety cover into your wall color instead of leaving a bright white plate on display. This guide walks through what to look for, how to prep and paint the covers without blocking the safety features, and how to install them so they stay put and keep little fingers out of the slots.
Choose the Right Paintable Cover for Your Outlets
Start by checking the outlet type and the wall plate size. Most standard duplex outlets use a single-gang cover, while some kitchens and offices use a two-gang or decorator-style plate. Measure the height and width of your current plate and compare it to the listing before you buy.
Shopping for one? See our guide: Outlet Plug Covers Lowe's: 6 Best Picks for Toddler-Safe Homes.
Look for covers marked as tamper-resistant or with sliding shutters that close when a plug is removed. The paintable part only matters if the child-safety feature is still working after you finish. Covers that are primed and ready for paint are usually sold as blank plates, so confirm the packaging says paintable and not pre-finished.
Prepare and Paint the Covers Correctly
Paint can clog shutters and slots, so prep is the step that matters most. Remove the cover from the wall first, then work on a flat, clean surface.
- Wipe each cover with a damp cloth and let it dry fully.
- Mask off the shutter openings, screw holes and any moving parts with painter’s tape.
- Apply one thin coat of primer suited to plastic or the cover material, and let it dry as the label specifies.
- Apply two thin coats of paint that matches your wall. Thin coats dry faster and are less likely to bridge the slots.
- Remove the tape once the paint is dry to the touch, and check that the shutters still slide freely.
Let the paint cure for the full time listed on the can before handling the covers heavily. Consult the paint manufacturer’s instructions for drying and recoat windows.
Install the Covers So They Stay Safe
Turn off the power at the breaker before removing any existing plate. Check the screw size on the new cover, since the wrong length can leave the cover loose or pinch the wiring. If the plate rocks after tightening, back the screws out slightly and retighten evenly.
Once installed, press a plug halfway into one slot and confirm the shutter opens only with the correct pressure. The cover should sit flush against the wall with no gaps for a child’s fingertip. If it does not, replace it rather than trying to force a fit.
Common Mistakes to Avoid
- Painting over the shutters, which can seize them shut or stop them from closing.
- Applying thick coats that drip into the slots.
- Skipping primer on glossy or plastic surfaces, leading to peeling.
- Overtightening screws, which can crack the cover.
- Using a color match that is noticeably off from the wall, which draws the eye back to the outlet.
Recommended Gear
A stiff-bristle brush or foam roller helps you apply thin, even coats without leaving drips in the slots. View on Amazon
Painter’s tape with a clean release keeps paint off the shutters and screw holes during prep. View on Amazon
A non-contact voltage tester lets you confirm the circuit is dead before you remove an old plate. View on Amazon
FAQ
Can I paint outlet covers that are already installed?
It is safer to remove them first, since paint can get into the shutters and screw holes while you work. Painting in place also makes it harder to get a smooth finish.
Do paintable covers still work as child-safety covers?
Yes, as long as you keep the shutters and moving parts free of paint and confirm they still close properly after painting. Check the shutters with a plug before reinstalling.
What if my outlet is an unusual size?
Measure your existing plate and compare it to the product listing before buying. If you are unsure, a licensed electrician can confirm the right fit and handle any wiring work.
Conclusion
Paintable outlet covers from Lowe’s can blend cleanly into your walls while still protecting toddlers, as long as you choose a tamper-resistant style and keep paint out of the shutters. Prep carefully, use thin coats and confirm the shutters still move before you reinstall. Follow the manufacturer’s instructions throughout.
