Updated November 2026

Outdoor outlet covers from Lowe’s can keep rain, dirt and curious little fingers away from exposed receptacles on your patio, deck or garage wall. This guide walks you through choosing the right style, checking your outlet before you buy, and installing the cover so it stays put and seals properly. Use it as a checklist on your next trip to the store or your next outdoor safety audit.

Step 1: Check the outlet type before you shop

Outdoor covers are sized for specific box configurations, so measure first. Look at the outlet itself: is it a single, duplex (two-gang) or GFCI receptacle? Note whether the box is a single-gang or a deeper two-gang box, and whether the outlet sits flush with the wall or is mounted in a raised “in-use” box. Lowe’s organizes covers by these categories, so bringing a photo of the outlet and its box helps you match the right part on the first try.

Shopping for one? See our guide: Outlet Plug Covers Lowe's: 6 Best Picks for Toddler-Safe Homes.

Step 2: Choose a cover rated for wet locations

Look for packaging that identifies the cover as weatherproof or rated for wet locations. Many manufacturers specify that an in-use cover is designed to stay closed while a plug is connected, which matters for toddler homes because it prevents a child from pulling on a cord and exposing the contacts. Flip-style and spring-loaded covers both close automatically, but check that the hinge and closing action work with the cord you actually plug in.

Step 3: Install the cover correctly

Before you start, turn off power at the breaker and confirm the outlet is dead with a non-contact voltage tester. Remove the old cover, inspect the box for cracks or corrosion, and replace the gasket if the new cover includes one.

  1. Gather a screwdriver, the cover, the gasket (if included) and a voltage tester.
  2. Turn off the circuit and verify no voltage is present at the receptacle.
  3. Seat the foam gasket flat against the wall around the box so no gaps show.
  4. Fasten the cover with the screws supplied, tightening until it is snug but not cracking the housing.
  5. Close the cover and check that it latches or seals without forcing it.
  6. Restore power and test the outlet with a plug.

If the box is damaged, the wiring looks old or the outlet is hot to the touch, stop and consult a licensed electrician before continuing.

Step 4: Plan for toddler safety on exterior walls

Outdoor outlets are often at a child’s height near play areas, so the cover should be hard to open for a toddler but easy for an adult. Covers with a locking tab or a sliding lock are one option, as described in Locking Outdoor Electrical Outlet Covers: A Step-by-Step Guide for Safe Installs. Also check the rest of the wall. Cords running from the outlet should not hang where a child can reach them, and the outlet should sit well clear of any water source.

Choosing between wall-matched and trim-matched finishes

Color mostly affects appearance, not safety, so choose a finish that suits your siding. If you want to decide between matching the wall or the trim, Should Outlet Covers Match Wall or Trim? Here's the Answer covers that question in more detail.

Common mistakes to avoid

  • Buying an indoor cover for an outdoor wall. Indoor covers rarely block moisture.
  • Skipping the gasket, which lets water run behind the plate.
  • Overtightening screws and cracking the housing.
  • Forgetting to turn off the circuit before swapping the cover.
  • Leaving a cord looped out of a closed cover where a child can pull it.
  • Non-contact voltage tester: Confirms the circuit is dead before you touch the box, which is the most important step in the job. View on Amazon
  • Replacement foam gaskets: Help the cover seal against the wall if the original gasket is worn. View on Amazon
  • Stainless steel outlet cover screws: Resist rust better than plain steel in damp outdoor boxes. View on Amazon

FAQ

Can I use an indoor outlet cover outside?

It is not recommended. Indoor covers are not designed to keep out rain, snow or spray, and they can let moisture reach the receptacle.

Do outdoor covers need a gasket?

Most weatherproof covers rely on a gasket to seal the gap against the wall. Check that one is included or replace it if it is damaged.

Should a licensed electrician install the cover?

Swapping a cover on a working, undamaged box is a straightforward task for most homeowners who turn off the power first. If the box is cracked, the wiring is unclear or the outlet shows signs of heat or damage, consult a licensed electrician.

Conclusion

Measure your outlet, choose a cover rated for wet locations, and install it with the power off and the gasket seated flat. Add a cover that resists a child’s curiosity and keep cords out of reach, and your exterior outlets will be both protected from weather and safer for toddlers.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our childproofing guides, checking product details against manufacturer specifications and owner feedback.