Updated November 2026

Outlet covers from Ace Hardware are a practical way to block curious fingers and objects from electrical receptacles. This guide walks you through choosing the right style, checking fit, and installing covers so they stay in place. Most of the work takes less than an hour for a typical room.

Choose the Right Type of Outlet Cover

Ace Hardware stocks several common styles, and each one suits a different situation. Standard plastic plug-in covers are the simplest option for outlets you rarely use. Sliding covers and self-closing receptacle covers work better for outlets you use daily, since you can open them without removing anything. Keep in mind that plug-in covers can be pulled out by a determined toddler, so they are best reserved for low-traffic outlets where a sliding or screw-in cover is not practical.

Shopping for one? See our guide: 7 Best Outlet Covers for Floor Installations Compared (2026).

Before buying, check your outlet type. Most US homes use standard duplex receptacles, but some older or specialized outlets have different faceplate sizes. If you are unsure, take a photo of the outlet to the store or measure the faceplate width and height.

Measure and Match Your Outlets

Covers are sized to fit specific faceplate dimensions. A cover that is slightly too large will sit loose, and one that is too small will leave gaps that small hands can reach into.

  1. Remove the existing faceplate and check whether it is a single, duplex, or GFCI receptacle.
  2. Measure the outer width and height of the faceplate, then compare these to the cover packaging.
  3. Confirm that the cover is labeled for the same number of gang positions as your outlet.
  4. Check that the cover can be installed over a GFCI outlet if your bathroom or kitchen uses one.

Install Your Outlet Covers Step by Step

Installation is simple, but a few details make the difference between a cover that stays put and one that works loose over time.

  1. Switch off the circuit at the breaker panel if you need to remove a faceplate, or simply leave the faceplate in place if the cover mounts over it.
  2. Clean the wall around the outlet so adhesive or mounting surfaces bond well.
  3. For screw-mounted covers, use the screws supplied with the product or the correct size for your faceplate. If you are unsure which screws to use, see our guide on What Size Screws for Outlet Covers? A Step-by-Step Guide for Toddler Homes.
  4. Press the cover firmly into place and test it by pulling gently in several directions.
  5. Confirm that the sliding door or latch closes fully and stays shut without forcing it.

Mounting Over Different Wall Surfaces

Drywall, plaster, and textured walls each handle fasteners differently. On drywall, a screw should anchor into the outlet box rather than the wall board. On plaster or textured walls, you may need to level the surface first to avoid a gap. Painted walls can also affect how well adhesive-based covers hold, so give paint a full cure time before mounting.

Compare Finishes and Colors

Ace Hardware carries covers in several colors, and the choice affects how noticeable they are. Covers that match your wall or trim tend to blend in, which many homeowners prefer. If you are weighing options, our article on Should Outlet Covers Match Wall or Trim? Here's the Answer covers the tradeoffs in more detail. For a broader view of style options, see Types of Outlet Covers: 5 Styles Compared for Toddler-Safe Homes.

Common Mistakes to Avoid

  • Buying covers without measuring the existing faceplate, which leads to loose or gapped fits.
  • Using plug-in covers on outlets a child can reach and pull out.
  • Forcing a cover onto a GFCI outlet without confirming compatibility.
  • Skipping the pull test after installation, which hides loose mounts.
  • Installing covers on exterior walls without checking for weatherproof ratings.

A basic set of tools makes installation faster and more reliable.

  • Non-contact voltage tester: confirms an outlet is dead before you touch it. View on Amazon
  • Phillips screwdriver set with insulated handles: useful for faceplate and screw-mount covers. View on Amazon
  • Digital caliper: helps you measure faceplate dimensions accurately before buying. View on Amazon

FAQ

Do Ace Hardware outlet covers fit GFCI outlets?

Many covers fit GFCI receptacles, but compatibility depends on the faceplate size and style. Check the packaging or measure your faceplate before buying.

Can I install an outlet cover without turning off the power?

If the cover mounts over an existing faceplate, you usually do not need to cut power. If you must remove the faceplate, switch off the breaker first and verify the outlet is dead with a voltage tester. Consult a licensed electrician if you are unsure.

How do I know if an outlet cover is secure enough for a toddler?

Screw-mounted or sliding covers with a locking or self-closing feature are more secure than plug-in types. Test the cover by pulling on it firmly after installation, and recheck it every few months.

Conclusion

Choosing the right Ace Hardware outlet cover comes down to measuring your faceplates, matching the cover type to how often you use each outlet, and installing it with a firm pull test. Take the time to confirm fit and mounting, and your covers will hold up. For a full room-by-room check, revisit each outlet every few months to confirm nothing has loosened.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our childproofing guides, checking product details against manufacturer specifications and owner feedback.