Updated November 2026

To wallpaper an outlet cover, you remove the cover plate, cut a piece of wallpaper slightly larger than the plate, apply it to the plate’s face, trim the edges, and reinstall the plate. The result matches your wall and still covers the live outlet. Because you are working near electrical hardware, the safety steps matter as much as the decorating.

Before You Start: Choose the Right Cover

Wallpapering works best on a plain plastic or metal cover with a flat face. Avoid covers with raised edges, sliding doors or built-in tamper-resistant shutters that you would need to remove to apply paper, because glue can jam the mechanism. If you need a tamper-resistant cover near a toddler, consider Leviton Electrical Outlet Covers: How to Choose and Install Them Safely before you decorate, so the protective features stay intact.

Shopping for one? See our guide: How Much Are Outlet Covers? Plastic vs Metal vs Tamper-Resistant (2026).

Step-by-Step: Wallpaper the Outlet Cover

  1. Turn off power to the outlet at the breaker and confirm it is dead with a non-contact voltage tester.
  2. Remove the cover plate by unscrewing the center screw. Keep the screw and set it aside.
  3. Lay the plate face-down on the wallpaper and trace around it. Cut the paper about 1 inch larger on every side.
  4. Apply a thin, even layer of wallpaper paste or a removable adhesive to the plate face. Avoid getting paste on the screw holes or the back.
  5. Press the paper onto the plate, smoothing from the center outward to push out air bubbles.
  6. Use a craft knife to cut the paper away from the screw holes and the plate edges. Cut carefully so the paper does not lift later.
  7. Let the plate dry flat for several hours, or as long as the adhesive label specifies.
  8. Reinstall the plate on the outlet box and tighten the screw until the plate sits flush against the wall, without overtightening.

Wallpaper Sizing and Pattern Matching

Match the pattern to the wall so the plate disappears. For a small repeating print, align the motif with the surrounding paper before you trim. For a large pattern, accept that some mismatch will show and choose a solid or texture-based paper instead. Lightweight wallpaper is easier to fold and trim around the screw holes than heavy vinyl.

Reinstalling and Checking the Fit

After reinstalling, check that the plate does not bulge and that the outlet still accepts plugs without resistance. If the plate sits proud of the wall, the outlet box may be too deep or the paper too thick, which can loosen the connection over time. Consult a licensed electrician if the outlet feels loose or warm.

Common Mistakes to Avoid

  • Skipping the power shutoff. Always confirm the circuit is dead before removing the plate.
  • Using too much paste, which can seep behind the plate and reach the wiring.
  • Covering the screw heads or screw slots with paper, which makes the plate hard to remove later.
  • Applying wallpaper to a cover that has moving parts or a sliding shutter.
  • Leaving the plate loose. A loose plate can expose wiring or let a child pull it free.
  • A non-contact voltage tester helps you confirm the outlet is dead before you start. View on Amazon
  • A sharp craft knife with replaceable blades gives clean cuts around screw holes and plate edges. View on Amazon
  • A removable wallpaper adhesive is easier to correct if the paper goes on crooked. View on Amazon

FAQ

Can I wallpaper a tamper-resistant outlet cover?

It is not recommended. Glue and paper can interfere with the internal shutters that block objects from entering the slots. Use a plain cover or a cover designed to be decorated instead.

Does wallpaper on an outlet cover affect its safety?

Thin paper applied to the face does not usually change how the cover works, but it can add bulk and loosen the fit. Check that the plate sits flush and that the outlet still holds plugs firmly.

What if I make a mistake while applying the paper?

Turn the power off, remove the plate, and start with a fresh piece of paper. Removable adhesive makes this easier. Do not try to pry the damaged paper off while the plate is on the wall.

Conclusion

Wallpapering an outlet cover is a simple way to make a wall look uniform, as long as you shut off power, keep adhesive away from the mechanism and reinstall the plate snugly. Choose a plain, flat cover and check the fit when you finish. If anything feels loose or warm, call a licensed electrician.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our childproofing guides, checking product details against manufacturer specifications and owner feedback.