Updated November 2026

Knowing how to install furniture anchors means you can keep a dresser or TV from tipping onto a child who climbs drawers or pulls on the top edge. The job takes an afternoon, needs basic tools, and comes down to three things: anchoring into a stud or solid backing, using the right hardware for the wall, and testing the result. This guide walks through each step for a typical toddler room or living area.

Gather Your Tools and Materials

Most installs go faster when everything is on hand before you start. You will typically need:

Shopping for one? See our guide: 7 Best Ace Hardware Furniture Anchors for Baby Proofing (2026).

  • A stud finder, plus a small level
  • A drill with bits sized to the anchor and screw manufacturer’s specs
  • A tape measure and pencil
  • The anchor kit, including wall straps or cables and screws
  • A screwdriver for the fasteners at the furniture end

Check the instructions that came with your kit for the recommended pilot hole diameter. Oversized holes are a common reason anchors pull loose later.

Find Solid Anchor Points on the Wall

The anchor is only as strong as what it screws into. Wall studs are the best target. Drywall alone will not hold a loaded dresser. Use a stud finder to locate studs, then confirm by drilling a small test hole. Studs in standard US framing are usually 16 inches apart on center, but that spacing varies, so measure rather than assume.

If the furniture sits where no stud lines up, you can use a wood backing board mounted to studs, or choose a heavy-duty wall anchor rated for the load. Read load ratings carefully, since they apply to specific materials.

Install the Wall Hardware

Mark the stud locations at the height you need, usually near the top of the furniture. Keep the anchor point as high as practical, since tip-overs begin at the top. Drill pilot holes, then drive the lag screws or hardware into the stud. Stop when the head is flush, and do not overtighten, as that can strip the wood.

  1. Mark two stud points on the wall, level across the piece.
  2. Drill pilot holes slightly smaller than the screw body.
  3. Drive the screws until snug and flush.
  4. Attach the strap or cable hardware to the screw heads.

Attach the Furniture End and Test the Setup

Fasten the other end of the strap or cable to the back or top of the furniture, using the screws included in the kit. Make sure the strap is taut but not pulling the piece away from the wall. Then test it: push firmly on the top corner from the front and from the side. The furniture should lean slightly at most and return to position. Recheck after a week, since fasteners can settle.

For more detail on specific systems, see Heavy Duty Furniture Anchors: How to Secure Dressers and TVs (Step-by-Step) and Wall Anchors for Furniture: A Step-by-Step Guide for Toddler Homes.

Common Mistakes to Avoid

  • Anchoring only into drywall without a stud or backing board.
  • Placing the anchor point too low on the furniture, which reduces leverage against a tip.
  • Skipping the pull test after installation.
  • Using screws shorter than the manufacturer specifies.
  • Forgetting to recheck anchors after moving furniture or adding weight.

A quality stud finder makes locating framing much more reliable than tapping walls. Stud finder View on Amazon is worth having if you plan to anchor several pieces.

A magnetic stud finder helps where wall surfaces are uneven. View on Amazon can help you confirm stud locations on painted walls.

A small torpedo level keeps your mounting line straight across the piece. View on Amazon fits easily into a tool bag.

FAQ

Can I install furniture anchors without drilling into studs?

Yes, but the holding power is much lower. Heavy-duty wall anchors or adhesive systems can work for light items, though studs or solid backing are the safer choice for dressers and TVs.

How high should the anchor point be?

Place the anchor as close to the top of the furniture as possible while keeping the strap accessible. Higher attachment points give more resistance against tipping.

Should I recheck anchors after installation?

Yes. Test the piece after installation and recheck the hardware periodically, especially after moving furniture or when children start climbing. Consult a professional installer if you are unsure about wall construction.

Conclusion

To install furniture anchors correctly, locate solid wall framing, mount hardware securely with the right screws, and attach the furniture end with a firm, slightly taut strap. Test every piece before relying on it. A few careful minutes now prevents a tip-over later.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our childproofing guides, checking product details against manufacturer specifications and owner feedback.