Updated November 2026
4our kiddies furniture anchors are a type of anti-tip hardware meant to keep dressers, bookcases and TV stands from tipping onto a child who climbs or pulls on them. This guide walks you through choosing the right anchor for your furniture, installing it correctly, and testing that it holds. The whole job takes about an hour for a typical bedroom.
Check What Your Furniture and Wall Can Support
Before you buy or install anything, find out what you are attaching to. Anchors only work as well as the surface they grip, so the first step is identifying your wall type and the furniture’s back panel.
Shopping for one? See our guide: 7 Best Ace Hardware Furniture Anchors for Baby Proofing (2026).
- Knock on the wall. A hollow, drywall sound means you need anchors rated for hollow walls or you need to locate studs.
- Use a stud finder to mark studs at 16 inches apart, which is standard in most US homes.
- Look at the back of the furniture. Solid wood or thick particleboard holds screws better than thin, laminated panels.
- Note the furniture’s height and weight. Tall, top-heavy pieces need the most attention.
If you are unsure whether a wall can take the load, a general contractor or handyman can assess it. This is worth doing for any heavy item, especially a flat-screen TV on a stand.
Install the Anchors Step by Step
Most anchor kits follow the same basic sequence: mount a bracket to the wall, attach a strap or cable to the furniture, and connect the two so the piece cannot rock forward. Follow the instructions included with your kit, since hole sizes and screw lengths vary by product.
- Locate the stud and mark the bracket position at a height that lets the strap sit snug against the furniture’s back top rail.
- Pre-drill pilot holes slightly smaller than the screw diameter to prevent splitting, especially in wood studs.
- Fasten the wall bracket with the screws supplied. Drive each one fully so the bracket does not wobble.
- Attach the strap or cable to the furniture’s back panel or a solid crossbar, not to a thin decorative panel.
- Connect the strap to the wall bracket and tighten so the furniture sits flush against the wall with no gap.
Use the Right Hardware for Hollow Walls
If you cannot hit a stud at the needed height, use toggle bolts or heavy-duty hollow-wall anchors rated for the furniture’s weight. Check the rating printed on the package and choose one that exceeds your furniture’s weight with margin. Do not rely on plastic expansion plugs alone for anything heavy.
Test the Anchor Before You Trust It
An installed anchor should hold without movement. Test it once it is in place, and recheck it every few months, since screws can loosen as wood settles.
- Push the top of the furniture firmly forward and to each side. It should not lift off the floor or pull the bracket.
- Look for gaps between the furniture and the wall. A gap means the strap is too loose.
- Check the bracket for movement, cracking or screws that back out.
- Repeat this test after moving the furniture, cleaning behind it, or whenever a child has been climbing on it.
Common Mistakes to Avoid
- Anchoring only to a thin back panel that can tear away under load.
- Using screws that are too short to reach solid wood or the stud.
- Skipping the pilot holes, which can split the wood and weaken the grip.
- Assuming one anchor is enough for a tall dresser. Two anchors spaced apart usually work better.
- Forgetting to recheck anchors after rearranging the room.
Recommended Gear
- Stud finder: Locating studs accurately is the most important part of a secure install, and a stud finder makes it much easier. View on Amazon
- Drill with a bit set: Clean pilot holes prevent splitting in wood and make screws drive straight. View on Amazon
- Level: A level keeps brackets straight so the furniture sits evenly against the wall. View on Amazon
FAQ
Can I install furniture anchors without drilling into the wall?
Some adhesive or no-drill options exist, but they generally hold less weight than screwed anchors. For heavy furniture or TVs, screws into a stud are the safer choice. You can read about renter-friendly options in Furniture Anchors No Drill: 6 Renter-Friendly Ways to Stop Tip-Overs.
How often should I check my furniture anchors?
Check them every few months and any time you move the furniture or notice a child climbing on it. Tighten any loose screws right away.
Do furniture anchors stop a TV from falling?
They reduce the risk of a TV or stand tipping forward, which is one of the main causes of serious injury. They do not replace good placement, so keep heavy items off the top of furniture. For TV-specific guidance, see Heavy Duty Furniture Anchors: How to Secure Dressers and TVs (Step-by-Step).
Conclusion
Securing dressers and TVs with anchors is one of the most effective steps you can take to prevent tip-over injuries. Find solid anchor points, install hardware that matches your wall, and test every connection. For a broader view of room safety, check out Baby Proofing Securing Furniture: A Room-by-Room Step-by-Step Guide. If you have questions about your home’s structure, consult a licensed contractor.
Related reading
- Wood Anchors for Furniture: A Step-by-Step Guide to Securing Dressers
- Where to Buy Furniture Anchors: 5 Best Picks for Baby Proofing (2026)
- Wall Anchors for Furniture: A Step-by-Step Guide for Toddler Homes
- No Drill Wall Anchors for Furniture: How to Anchor Dressers Safely
- Heavy Duty Furniture Anchors: How to Secure Dressers and TVs (Step-by-Step)
- Furniture Anchors: Stopping TV and Dresser Tip-Overs
